Thank you for the information!
I contacted Ventline directly and confirmed that the Replacement Damper For Ventline RV Range Hoods With Vertical Exhaust # VA0478-02 is a confirmed replacement for any of the vertical exhaust range hoods offered by Ventline including the PR6 Range Hood you mentioned. view full answer...
I would be happy to help you find a 12" deep range hood. I am not sure whether you want a 20" wide or 22" wide hood so I found both. These range hoods are efficient, and the single-speed fan pulls air through the filter and vents it out. The aluminum mesh grease filter is removable for easy cleaning. These are the same model hoods with the exact same function. The only difference is the width.
20"- Ventline Pinnacle Ductless RV Range Hood with Light - 12V - 20" Wide - Black
Item # VE26SR
22"-... view full answer...
The Ventline Pinnacle RV Range Hood with Light - 12V - 22" Wide - Black # VE78SR is just for 12V DC, not AC. You could use a converter such as Go Power RV Converter and Smart Battery Charger - 12V - 55 Amp # 34266169 to convert AC to DC and run this range hood if you indeed have AC power only. view full answer...
The Ventline S0721 Series RV Range Hood w/ Light - 12V Fan part # S0721-20GC-F-1 is your best option for a range hood if your last hood melted. It includes a 12V fan to dissipate the heat and vent exhaust fumes through the trailer's wall compared to other hoods that just use air filters which allows the hood to overheat. The whole range hood is stainless steel except for the fan but can easily be wiped down. view full answer...
The duct opening on the back of the Furrion Ducted RV Range Hood with Light # FHO23SACRBP is 10" long x 3-1/4" tall so you would want a vent like the Ventline Exterior Wall Vent for RV Range Hood # V2111-55 ( # V2111-13 for white) or the Ventline Exterior Wall Vent for RV Range Hood # V2111-03.
The # V2111-55 has a 1-3/4" collar, while the # V2111-55 has a 5/8" collar. You'll want to measure the depth of your trailer's walls to choose the correct size collar. Any gaps can be covered with... view full answer...
The Replacement Fan Blade for Furrion RV 12-Volt Range Hoods part # FR63MR is not threaded. If you remove the nut you can pull it straight off. view full answer...
The motor that comes with the Ventline S0721 Series RV Range Hood S0721-20BD-F-1 is a single speed motor so you unfortunately aren't able to run it at a lower speed. You can replace the entire setup (since the replacement motor is no longer avialable) with the Ventline Pinnacle Ducted RV Range Hood which comes in Black # VE38SR or Black w/ Stainless Steel # VE98SR. These also have a single speed motor but they are different motors than what came in your range hood.
Range hoods aren't tested... view full answer...
If you had a way to direct the air flow of the Greystone Range Hood part # 324-000085 above the hood you certainly could using duct work, but there isn't a way to orientate the current vent on the hood to push out air through the top of it. view full answer...
We currently carry only two options that would fit with the dimensions you're looking for that and that are ductless since you don't already have a duct ran to vent out air from your stove.
Option 1: Ventline Pinnacle Ductless RV Range Hood with Light - Black # VE26SR
Option 2: Ventline Pinnacle Ductless RV Range Hood with Light - Black w/ Stainless Steel # VE58SR
I recommend going with whichever matches the aesthetics of your camper since the only difference is that the # VE58SR has... view full answer...
In regards to the Furrion RV Range Hood, the correct replacement fan blade is the Replacement Fan Blade for Furrion RV 12-Volt Range Hoods part # FR63MR. In order to replace this, you'd simply need to remove the nut on the end of the shaft and swap the two out. If you have some melted plastic on the end of the shaft then you can try to heat this up before removing the nut but you may be able to remove the nut along with the plastic then just clean up any excess after. If you had melted... view full answer...
If the range hood in your 2006 Itasca is a Ventline P, B, or T Series range hood with the horizontal exhaust, then the Replacement Damper # BCA0472-00 will work great for you.
If you do not have a Ventline range hood the damper may work but there is no guarantee. The overall dimension of this damper is 9-7/16 inches long x 4-1/2 inches wide. view full answer...
You're correct that the Furrion Ducted RV Range Hood with Light # FHO23SACRBL rear vent is only 5-7/8" long x 3-1/4" tall, whereas our vents are all larger at 10-1/2" wide x 3-3/4" tall. Typically there will be some insulation in the wall only allowing for a small bit of room for air to escape from the range hood and out the exterior vent. This is pretty typical is a residential setting as well. If you wanted to better control the way if vents you could also use HVAC tape to seal up the... view full answer...
Ventline exterior wall vent # V2111-55 has the same measurements as the white version # V2111-13 so either one will work with Range Hood # S0721-20BD-F-1. view full answer...
Ventline S0721 Series RV Range Hood # S0721-24BD-F-1 measures 24-inches wide and it requires a cabinet depth of 12-inches (meaning 6-inches of the hood's 18-inch total depth extends forward of the cabinet surface). If your cabinets are 18-inches deep this means that the entire depth of the hood will be under the cabinet when installed. This should not pose any issues.
Please feel free to let me know the side-to-side and front-to-back dimensions of your mounting location in the trailer... view full answer...
Technically yes, without screws you can use the Ventline Exterior Wall Vent for RV Range Hood - Locking Damper - 1-3/4" Collar - Black # V2111-55.
But I wouldn't recommend doing so, in all honesty; for a completely secure install, you will definitely want to use screws. view full answer...
If you are referring to one of the Ventline P, S0721, B, and T Series range hood, the Replacement 12-Volt DC Fan Motor for Ventline RV Range Hood # BVD0218-00-R would not require you to use a resistor or fuse to install it. It sounds like you could be replacing an older style motor, which if so means you will need a new fan blade like part # BVD0216-00. If the main body of your motor measures 2 inches then you have an older model motor. See picture. view full answer...
Since the Greystone Euro Style RV Range Hood # 324-000089 has a 6 inch duct you'd need a 6 inch to 4 inch duct reducer to fit this to a 4 inch duct. We don't offer this but they are easily available at local hardware stores to you. view full answer...
The Ventline Pinnacle Ducted RV Range Hood with Light # VE38SR you referenced is only compatible with a 12v DC power source so it would not work with the current wiring you have in place. Since we don't currently offer any 20" wide ranges that run off of 110v AC you'd have to run new wire for the range to your power center/DC fuse board in order to power it. view full answer...
I do have some exterior range hood vent options for you but you'll need to determine which is correct for your application based on the shape/size/color etc. as we have no way to look this up for you. Furthermore, you'll need to replace the entire assembly not just the flap portion. The Ventline Exterior Wall Vent for RV Range Hood part # V2111-13 for example is for 10-1/2" wide x 3-3/4" tall rough openings.
I have attached a few other options below. view full answer...
Go To Results